Commercially available Mobile WiMAX is here! Major networks have successfully rolled out worldwide with Clearwire in the U.S., UQ Communications in Japan, and Yota in Russia taking center stage. While existing networks are planning expansions, new operators are clearing paths for network launches very soon. With more and more multi-media hungry notebooks, netbooks, tablets, and smart phones anticipated to enter the world market, the existing WiMAX network capacity will get severely contrained.
WiMAX Release 2.0 (IEEE802.16m) which is a major amendment ( full backward compatibility) to the WiMAX Release 1.o (IEEE802.16e-2005) standard will offer significantly greater capacity, coverage and performance, and lower latency in order to meet the ITU-R requirements for an IMT -Advanced 4G technology solution. With remarkable design improvements in the advanced air interface architecture (new blocks inside Layer 1 and 2), 802.16m will be able to easily provide the necessary capacity that operators will demand to further grow their urban networks as well as to reliably deliver data at extremely high speeds (e.g. up to 120Mbps down and 60Mbps up using a 4×2 MIMO/TDD 5:3 configuration) to users.
As an example, in today’s WiMAX Network deployments, user devices connect to a single channel frequency utilizing a 5msec frame structure with time-division duplexed (TDD) DL and UL information using a 10MHz bandwidth. With 802.16m, user devices will be able to connect to two different channel frequencies (multi-carrier) at the same time utilizing the following possible combinations: 1) two independent 20msec super-frames each using a 10MHz bandwidth, 2) two independent 20msec super-frames each using a 20MHz bandwidth, and 3) one 20msec super-frame using a 20MHz bandwidth and the other 20msec super-frame using a 10MHz bandwidth – Hence, 20MHz (doubles today’s data transfer rates), 40MHz (quadruples today’s data transfer rate), and 30MHz (triples today’s data transfer rate), respectively. More so, the two carriers (radio frequencies) are not necessarily in adjacent bands. If they are in adjacent bands, then the guard bands can be used to transfer data. Digging deeper, a 20msec super-frame is divided into four 5msec radio frames with each radio frame further sub-divided into eight 0.617msec sub-frames. Each of the eight sub-frames per radio frame contains legacy zones for existing 802.16e devices and high-speed zones for new 802.16m devices. Within each of the four radio frames, a variety of DL/UL combinations ( 6/2, 5/3. etc.) can be achieved using various TDD, FDD and HFDD schemes which makes it possible to reduce the one-way air-link latency from 18.5sec (802.16e) to 5msec (802.16m).
Utilizing critical features such as multi-hop relay architecture, multi-carrier operation, self-configuration, multi-antenna schemes (Single – User and Multi-User MIMO), interference mitigation, enhanced multi-cast broadcast, increased VoIP capacity, improved cell-edge throughput, increased vehicular speeds (up to 500km/hr) and so forth, 802.16m is poised as the 4G broadband internet connectivity technology of choice well into this decade.
Sanjiv S. Gupta (Intel)
Sanjiv S. Gupta is a Senior Technical Marketing Engineer at Intel Corp with focus on WiMAX enablement world wide – primarily in U.S., Latin America, India and the EU. He has been with Intel Corporation for twelve years and has been directly responsible for the marketing/integration of Intel’s graphics and wireless components into OEM PCs
Photo courtesy of William Hook
Sanjiv S. Gupta (Intel)
Sanjiv S. Gupta is a Senior Technical Marketing Engineer at Intel Corp with focus on WiMAX enablement world wide – primarily in U.S., Latin America, India and the EU. He has been with Intel Corporation for twelve years and has been directly responsible for the marketing/integration of Intel’s graphics and wireless components into OEM PCs
Visit Going WiMax, the premier website in the industry for 'Everything WiMax' ! Read more about WiMax, 4G, LTE and Wireless technology at www.goingwimax.com
SOURCE